A New Fall Jacket: the “Moto-blazer”

WithNeedleAndThread-MotoBlazerI’d been wanting (to make) a moto/biker-style jacket for a while, buy hadn’t found a pattern that spoke to me, so the project kept getting bumped further and further down my “to make” list. Included in my list of wishes for my jacket were that it: have an asymmetrical but mostly straight zipper (versus a diagonal zipper), have an actually collar (not just the lapels), have traditional two-piece sleeves with no gussets, zippers, buttons, or extra seams, and that it be fitted rather than boxy, ideally with princess seams.

In other words, I wanted a cross between a classic moto-style jacket and a traditional blazer. Once I came to that epiphany, I decided to set about making my own “frankenpattern” (an oh so technical term for when you combine two or more different patterns to create one new pattern…think Frankenstein). I debated between several different moto jacket patterns before deciding on Simplicity 2056, which had the collar, lapels, and straight-off-center front that I had envisioned. For the blazer portion, I used Lekala 4162, a classic blazer pattern which I’ve made before and know fits well.

I traced the front of the Simplicity pattern onto the front piece of the Lekala pattern, lining up the shoulders and center fronts. When I cut the traced pattern out, I kept the center front part of the moto jacket and blended into the armscye princess seam lines of the blazer. In the photo below, the purple is the Lekala pattern, the teal is the moto jacket, and the red should be ignored (I traced two sizes of the moto jacket and ended up going with the smaller one – this is the larger one).

WithNeedleAndThread-MotoBlazer

In addition, I used the side front, side back, back, and sleeves from the Lekala pattern, and the collar and pocket pieces from the moto jacket pattern. About halfway though the project, I started calling my jacket a “moto-blazer,” and I think that name is going to stay with it.
Based on the pattern envelope images, I thought that the moto jacket collar may be too big for me, so I basted it on before sewing it for real. And it did turn out too big; I would up narrowing it by increasing the seam allowance along the back seamline, taking 1.5” from the corner, tapering to .75” at center back, then back out to 1.5” at the other corner. I probably could have made it smaller still, but decided to embrace the slightly oversized collar to give the jacket even more of a different look from the other jackets in my closet.

WithNeedleAndThread-MotoBlazerSince I had changed the fit of the moto jacket and was changing the pocket style of the blazer pattern, I added the pockets after I’d sewn most of the jacket, but before attaching the lining. This allowed me to determine the ideal length and placement of the pockets as they would fall when I was actually wearing the jacket. I think my pockets ended up being a bit smaller than a traditional pocket, but they work on me. And I don’t really intend to use the pockets for much, so going smaller with the pockets wasn’t an issue. This was the first time I’ve put zippered pockets in a jacket, and I initially found the idea of cutting a whole in my jacket slightly terrifying. Of course, in reality, it wasn’t nearly as bad as I’d built it up to be in my head and I’m glad I went ahead and put in the pockets/zippers.

After the jacket shell was mostly finished (and pockets mentioned above inserted), I decided that I really didn’t like the look of the partially exposed zipper that I was originally intending to use (the left zipper piece had no seam to be sewn into…which I hadn’t fully taken into consideration when combining my patterns as the Simplicity pattern originally called for buttons rather than a zipper on the view I used). Luckily, I had enough wiggle room (or extra ease that could be un-eased) that I was able to taper the top edge of the zipper tape, and fold the jacket fabric over the edge of the zipper tape to create a faux-seam. If/when I make this pattern again, I’d probably draft a real seam into the pattern here as I like this look much better than the exposed zipper look.

The fabric is a wool blend coating that I got from Fabric.com a few years ago. Though it’s hard to see in my pictures, it is a blend of cream/tan, olive, purple, and mustard yellow threads. I lined the jacket with purple Bemberg lining.

Zipper issues aside, I am happy with the way my new “moto-blazer” turned out and am now anxiously waiting for the weather to cool down enough so that I can wear my new jacket.

 

Advertisements